Tru-Tension Mega Tool Bundle Chain Monkey & Laser Monkey
The pinnacle bundle combination for precision chain tension and wheel alignment.
Load your Chain Monkey onto the chain and set to the setting required for your motorcycle. Clamp your Laser Monkey onto the sprocket and point the laser as far down the chain as possible. Adjust your chain until the laser is showing in the centre of the chain while the slack has just been removed from the chain…and you’re done!
The ultimate tool bundle to maximise the output and performance of your motorcycle.
How to use your Chain Monkey
Before you begin, remove black plastic cap from domed nut.
Step 1: Using your motorcycle’s manufacturer manual, specify how much slack your chain requires in mm or inches. Measure the size of your chain and use the table to identify your required Chain Monkey setting.
Step 2: Align bottom of domed nut with required setting line and adjust circular stop until it touches the orange base.
Step 3 :Hook on to chain and tighten until circular stop touches the orange base.
Step 4: Tighten chain until all slack is removed while centralising wheel.
Step 5: Remove from chain. Required tension will now be set.
How to use your Laser Monkey
Step 1: Remove screws from the top of the Laser Monkey using Allonkey provided.
Step 2 :Ensure laser is pointing at the floor. Place the two batteries provided in the space behind the laser. Negative terminal of batteries to connect with laser spring.
Step 3: Position head back onto body ensuring switch terminal fits behind both batteries. Screw the three screws back into head to secure in place.
Step 4: Widen the arms on the Laser Monkey outwards by twisting the adjuster to allow enough space to fit over your chain or belt.
Step 5: Pass the Laser Monkey over the chain/belt and adjust the arms inwards until they grip a flat part of the rear sprocket/pulley. Ensure the Laser Monnkey is gripping to clean, dirt free, flat parallel surfaces.
Step 6: Point the laser down to the closest part of the chain/belt and turn on. The laser should appear in the centre of the chain link or belt. If not centralised initially, adjust positioning to centralise the laser.
Step 7: Lift the laser head to point at the furthest visible point of the chain/belt towards the engine. Adjust the wheel alignment until the laser is showing at the centre point of the chain/belt. Your wheel will then be accurately aligned.
Step 8: Lock the rear axle nuts and adjustment nuts, turn off the laser and remove the Laser Monkey from your sprocket or pulley.
Warning: Do not shine laser directly in eyes or at anything other than its intended use.
The pinnacle bundle combination for precision chain tension and wheel alignment.
Load your Chain Monkey onto the chain and set to the setting required for your motorcycle. Clamp your Laser Monkey onto the sprocket and point the laser as far down the chain as possible. Adjust your chain until the laser is showing in the centre of the chain while the slack has just been removed from the chain…and you’re done!
The ultimate tool bundle to maximise the output and performance of your motorcycle.
How to use your Chain Monkey
Before you begin, remove black plastic cap from domed nut.
Step 1: Using your motorcycle’s manufacturer manual, specify how much slack your chain requires in mm or inches. Measure the size of your chain and use the table to identify your required Chain Monkey setting.
Step 2: Align bottom of domed nut with required setting line and adjust circular stop until it touches the orange base.
Step 3 :Hook on to chain and tighten until circular stop touches the orange base.
Step 4: Tighten chain until all slack is removed while centralising wheel.
Step 5: Remove from chain. Required tension will now be set.
How to use your Laser Monkey
Step 1: Remove screws from the top of the Laser Monkey using Allonkey provided.
Step 2 :Ensure laser is pointing at the floor. Place the two batteries provided in the space behind the laser. Negative terminal of batteries to connect with laser spring.
Step 3: Position head back onto body ensuring switch terminal fits behind both batteries. Screw the three screws back into head to secure in place.
Step 4: Widen the arms on the Laser Monkey outwards by twisting the adjuster to allow enough space to fit over your chain or belt.
Step 5: Pass the Laser Monkey over the chain/belt and adjust the arms inwards until they grip a flat part of the rear sprocket/pulley. Ensure the Laser Monnkey is gripping to clean, dirt free, flat parallel surfaces.
Step 6: Point the laser down to the closest part of the chain/belt and turn on. The laser should appear in the centre of the chain link or belt. If not centralised initially, adjust positioning to centralise the laser.
Step 7: Lift the laser head to point at the furthest visible point of the chain/belt towards the engine. Adjust the wheel alignment until the laser is showing at the centre point of the chain/belt. Your wheel will then be accurately aligned.
Step 8: Lock the rear axle nuts and adjustment nuts, turn off the laser and remove the Laser Monkey from your sprocket or pulley.
Warning: Do not shine laser directly in eyes or at anything other than its intended use.
The pinnacle bundle combination for precision chain tension and wheel alignment.
Load your Chain Monkey onto the chain and set to the setting required for your motorcycle. Clamp your Laser Monkey onto the sprocket and point the laser as far down the chain as possible. Adjust your chain until the laser is showing in the centre of the chain while the slack has just been removed from the chain…and you’re done!
The ultimate tool bundle to maximise the output and performance of your motorcycle.
How to use your Chain Monkey
Before you begin, remove black plastic cap from domed nut.
Step 1: Using your motorcycle’s manufacturer manual, specify how much slack your chain requires in mm or inches. Measure the size of your chain and use the table to identify your required Chain Monkey setting.
Step 2: Align bottom of domed nut with required setting line and adjust circular stop until it touches the orange base.
Step 3 :Hook on to chain and tighten until circular stop touches the orange base.
Step 4: Tighten chain until all slack is removed while centralising wheel.
Step 5: Remove from chain. Required tension will now be set.
How to use your Laser Monkey
Step 1: Remove screws from the top of the Laser Monkey using Allonkey provided.
Step 2 :Ensure laser is pointing at the floor. Place the two batteries provided in the space behind the laser. Negative terminal of batteries to connect with laser spring.
Step 3: Position head back onto body ensuring switch terminal fits behind both batteries. Screw the three screws back into head to secure in place.
Step 4: Widen the arms on the Laser Monkey outwards by twisting the adjuster to allow enough space to fit over your chain or belt.
Step 5: Pass the Laser Monkey over the chain/belt and adjust the arms inwards until they grip a flat part of the rear sprocket/pulley. Ensure the Laser Monnkey is gripping to clean, dirt free, flat parallel surfaces.
Step 6: Point the laser down to the closest part of the chain/belt and turn on. The laser should appear in the centre of the chain link or belt. If not centralised initially, adjust positioning to centralise the laser.
Step 7: Lift the laser head to point at the furthest visible point of the chain/belt towards the engine. Adjust the wheel alignment until the laser is showing at the centre point of the chain/belt. Your wheel will then be accurately aligned.
Step 8: Lock the rear axle nuts and adjustment nuts, turn off the laser and remove the Laser Monkey from your sprocket or pulley.
Warning: Do not shine laser directly in eyes or at anything other than its intended use.